济南立强模具有限公司是一家提供济南注塑模具注塑加工等产品的山东模具制造厂家

山东济南注塑模具制造加工

     

新闻动态

您现在的位置: 网站首页>>新闻动态>>塑胶注塑加工操作时需要注意什么?

塑胶注塑加工操作时需要注意什么?

来源:http://www.sdlqmj.com 日期:2020-06-12 发布人:liqiang 浏览次数:

 

Jinan injection molding
一、生产工艺调整:
1、 Production process adjustment:
1、首先,工艺参数是否与实际模型、材料、模具相同;
1. First, whether the process parameters are the same as the actual model, material and mold;
2、同时,当输入工艺参数时,啤酒稍微降低压力速度,然后逐渐调节(根据产品质量比);
2. At the same time, when the process parameters are input, the first beer slightly reduces the pressure speed, and then gradually adjusts (according to the product quality ratio);
3、操作工生产;
3. Operator production;
4、检查机器安全调较是否安全。
4. Check whether the safety adjustment of the machine is safe.
二、操作人员是否熟悉生产前产品的质量标准:
2、 Are operators familiar with the quality standards of products before production
1、塑料注射成型厂阐述,加工方法应正确,如:喷嘴位置必须切割平或平,其他边缘部位不可擦伤或切割;
1. The plastic injection molding factory stated that the processing method should be correct, such as: the nozzle position must be cut flat or flat, and other edge parts cannot be scratched or cut;
2、检查外观有无收缩、混匀、顶高、缺胶、料花等,更终收料程度不一定清楚;
2. Check the appearance for shrinkage, mixing, top height, lack of glue, material bloom, etc., and the final material receiving degree is not necessarily clear;
3、外观要求严格的产品,如镜面、旋钮、光滑表面等,未经喷涂和外部组装,不得有手印油点等。工作台应保持清洁,不得划伤、划伤产品;
3. Products with strict appearance requirements, such as mirrors, knobs, smooth surfaces, etc., shall not have hand printed oil spots without spraying and external assembly. The worktable shall be kept clean, and products shall not be scratched or scratched;
4、每30分钟对产品进行全面检查,认真检查样品和质量检验包装说明书,确保生产产品合格率达到100%;
4. Carry out a comprehensive inspection of the products every 30 minutes, carefully check the samples and quality inspection packaging instructions, and ensure that the qualified rate of the production products reaches 100%;
5、同时注意机器喷嘴是否漏胶,漏斗是否需要进料,模具是否有问题,生产任务是否每小时完成;
5. At the same time, pay attention to whether the machine nozzle leaks, whether the funnel needs feeding, whether the mold has problems, and whether the production task is completed every hour;
6、塑料注射成型厂概况,一盒填写完毕仔细检查数量,正确填写商标纸,注意是否贴错了标签,并将货物放进指定区域,整齐摆放。
6. Overview of plastic injection molding plant, carefully check the quantity of a box filled in, correctly fill in the trademark paper, pay attention to whether the wrong label is pasted, and put the goods in the designated area in order.

相关新闻

地址: 济南市天桥区太平庄药山镇丁庄工业园8号; 网址:http://www.sdlqmj.com  传真:0531-61388458   手机:18610627886

Copyright © 2018 济南立强模具有限公司   版权所有  鲁ICP备15002024号-2   技术支持:济南诺商 流量统计: