济南立强模具有限公司是一家提供济南注塑模具注塑加工等产品的山东模具制造厂家

山东济南注塑模具制造加工

     

新闻动态

您现在的位置: 网站首页>>新闻动态>>使用塑料模具时应该注意哪些事项

使用塑料模具时应该注意哪些事项

来源:http://www.sdlqmj.com 日期:2019-01-01 发布人:admin 浏览次数:
使用塑料模具时应该注意哪些事项?
What should we pay attention to when using plastic moulds?
对于塑料模具,大家应该有所了解了,但是在使用塑料模具时,应该注意哪些事项大家知道吗?
For plastic moulds, you should know something, but when using plastic moulds, what should you pay attention to?
1 .放置预制件的场地必须平整。
1. Place prefabricated parts on a flat surface.
2 .预制之前模具内须擦脱模剂或脱模油。。
2. Before prefabrication, the release agent or the release oil must be wiped in the mould.
3 .装有混凝土的模具必须放平整。
3. Moulds with concrete must be laid flat.
4 .禁止在4度以下预制构件。
4. Prefabricated components below 4 degrees are prohibited.
5 .脱模后暂时不用的模具必须在清理后摆放整齐。防止变形。
5. Moulds not used temporarily after demoulding must be placed neatly after cleaning. Prevent deformation.
6 .脱模时使用的敲击工具必须是木锤或皮锤。
6. The knocking tool used in demoulding must be a wooden hammer or a leather hammer.
7 .脱模时要用脱模器或下面垫麻袋片或垫稻草袋或废轮胎,以防损坏预制件和模具。
7. To prevent damage to prefabricated parts and moulds, a demoulding device or a flax bag or straw bag or waste tire should be used.
8 .震动平台上要经常清理,保持平整,收工时清理干净。
8. The vibration platform should be cleaned regularly, keep smooth and clean up after work.
山东模具制造厂家
9 .预制较大构件时,若模具直接放在地上用振动棒时,振动棒头上必须套上皮套,否则可能减少模具使用寿命。
9. When prefabricating larger components, if the die is placed directly on the ground with the vibrating rod, the head of the vibrating rod must be covered with an epithelial sleeve, otherwise the service life of the die may be reduced.
10 .预制较大构件或较重构件时容易变形,建议使用木板夹好或使用卡子或使用做好的铁框子。
10. Prefabrication of larger or reconstructed components is easy to deform. It is recommended to use wooden boards, clips or iron frames.
11 .夏天温度较高时预制构件必须蒙上麻袋片或稻草袋或遮阳网,以防太阳晒裂预制件,并按时洒水养护。
11. When the temperature is high in summer, the prefabricated components must be covered with sacks or straw bags or shading nets to prevent the sun from cracking the prefabricated parts and be maintained by sprinkling water on time.
12 .需要做带孔的预制块时所用的管子必须及时抽出,放止时间长了抽不出来。
12. When making prefabricated blocks with holes, the pipes used must be pulled out in time, and they can not be pulled out for a long time.
13 .模具上粘有水泥不好清理时,禁止用铁制工具清理,建议用稀盐酸或草酸沁泡,之后用软布清理。
13. It is forbidden to clean the mould with iron tools when cement is not good to clean. It is suggested to use dilute hydrochloric acid or oxalic acid to soak, and then clean it with soft cloth.
以上内容有济南立强模具有限公司提供,想了解更多知识点欢迎关注我们山东模具制造厂家http://www.sdlqmj.com谢谢!!
The above content is provided by Jinan Liqiang Mould Co., Ltd. For more knowledge, please pay attention to our Shandong Mould Manufacturer http://www.sdlqmj.com, thank you!!

相关新闻

地址: 济南市天桥区太平庄药山镇丁庄工业园8号; 网址:http://www.sdlqmj.com  传真:0531-61388458   手机:18610627886

Copyright © 2018 济南立强模具有限公司   版权所有  鲁ICP备15002024号-2   技术支持:济南诺商 流量统计: